Fmi STH/Q Bedienungsanleitung PDF herunterladen

Before using any Fluid Metering, Inc. product read the following safety instructions

as well as specific product specifications and operating instructions.

Warning!

Fire, electrical shock or explosion may occur if used near combustibles

xplosive atmosphere, corrosive air, wet environment or submerged in fluid.

Caution! Fire, electrical shock, injury and damage may

occur if not used in accordance with Fluid Metering, Inc.

specifications and operation instructions.

Do not put wet fingers into power outlet of unit.

Do not operate with wet hands.

Do not operate drive assemblies that require a hard mount

(to be bolted down) unless they are mounted per Fluid Metering, Inc.

specifications, if not injury may occur and/or damage to unit.

Do not touch any rotating pump or motor components: injury may

occur.

Do not run pump dry, unless designed for that service.

Running dry is harmful to the pump, and will cause excessive heating

due to internal friction.

Check pump rotation and inlet/outlet pump port orientation before

connecting power to pump. If not injury may occur.

When pulling out cords from outlets do not pull cord, grasp plug to

prevent plug damage or electrical shock.

Fluid Metering, Inc. Drive Motors become HOT and can cause

a burn

. DO NOT TOUCH!

Disconnect electrical power before checking pump for any problems.

Connect motor, speed controllers, or any other electrical devices

based on Fluid Metering Inc. specifications. Any unauthorized work

performed on the product by the purchaser or by third parties can

impair product functionality and thereby relieves Fluid Metering, Inc.

of all warranty claims or liability for any misuse that will cause

damage to product and/or injury to the individual.

Power cables and leads should not be bent, pulled or inserted by

excessive force. Otherwise there is a threat of electrical shock or fire.

Replace any inline fuses only with fuse rating as specified by Fluid

Metering, Inc.

When pump/drive is under operation, never point discharge tubing

into face or touch any rotating components of pump.

In a power down thermal overload cut-in condition, unplug or turn off

power to pump. Always allow a cool down period before restarting:

otherwise, injury or damage may occur.

For 30 seconds after power is removed from pump/drive: do not

touch any output terminals. Electrical shock may occur because of

residual voltage.

2.0 GENERAL SET-UP

2.1 Setting Dispense Stroke Rate

Strokes Per Minute (spm): For fluids of 500cps

viscosity or less a stroke rate of 120-350 spm max is

ideal. For fluids with greater than 500cps a slower rate

is recommended.

2.2 Fluidics:

Inlet (Suction) Tubing: To avoid cavitation use the

most resilient tubing possible with the largest

inside diameter (I.D.)

Outlet (Dispense) Tubing: For best dispense

performance use rigid Teflon tubing (to reduce

peristaltic action) with an equal or smaller I.D. than the

inlet (suction) tubing.

REQUIRED TOOLS:

1. Analytical Pan Balance

2. Hex Key Driver for Adjusting Stroke Length:

STH: 3/32" Hex Driver

STQ: 7/32" Hex Driver

3. A removable wicking thread lock (loctite 290)

1.0 PUMP MOUNTING: For optimum pump per-

formance it is recommended that your FMI pump

be mounted in a vertical position with the pump

head down in a 6:00 o'clock position and the motor

at 12:00 o'clock. This orientation will allow air bub-

bles that enter the pumping chamber to directly exit

through buoyancy assistance. Figure A

Figure A

www.fmipump.com [email protected] 800-223-3388 516-922-6050

SAFETY INSTRUCTIONS

IN-ST431-14

STH/Q SET UP INSTRUCTIONS

FOR ADDITIONAL REFERENCES SEE H431 AND Q431

1 2 3 4 5 6 7

Inhaltsverzeichnis

Seite 1 - STH/Q SET UP INSTRUCTIONS

1Before using any Fluid Metering, Inc. product read the following safety instructions as well as specific product specifications and operating instruc

Seite 2 - Flag Edge Approaching Sensor

2.3 Step Motors:FMI ST pumps are supplied with a 17 or a 23frame Motors. For wiring diagram and detailed motor specifications go to the literature se

Seite 3 - IN-ST431-14

The design of FMI Pumps is unique throughout theworld. Having no valves and only one moving part,“the piston” makes this design very special. No valve

Seite 4

With the Pump/Drive Assembly removed from theinstrument and the piston/cylinder group removed(MAY REQUIRE PUMP RECALIBRATION):b) If the pump is severe

Seite 5 - Figure D

IN-ST431-145Figure BFigure C3.0 CALIBRATION AND TESTING3.1 Flush the system: clean with alcohol or other suitable cleaning/wetting agent before using

Seite 6

3.4 Dispense Volume Values for FMI STH/STQPumps:NOTE: To assure the best performance set thepump displacement volume as large as possible. FMI pumps

Seite 7 - Rotational Sensor

IN-ST431-147Figure ENOTE:FOR ADDITIONAL REFERENCES SEE H431 AND Q431VccVcc* NOT SUPPLIED WITH OPTICAL SENSORS See suggested Rd values table below

Kommentare zu diesen Handbüchern

Keine Kommentare

Fmi STH/Q Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Pumpen Fmi STH/Q herunter. FMI STH/Q User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Pumpen Fmi STH/Q