Fmi IDS Bedienungsanleitung PDF herunterladen

Before using any Fluid Metering, Inc. product read the following safety instructions

as well as specific product specifications and operating instructions.

Warning!

Fire, electrical shock or explosion may occur if used near combustibles

explosive atmosphere, corrosive air, wet environment or submerged in fluid.

Caution! Fire, electrical shock, injury and damage may

occur if not used in accordance with Fluid Metering, Inc.

specifications and operation instructions.

Do not put wet fingers into power outlet of unit.

Do not operate with wet hands.

Do not operate drive assemblies that require a hard mount

(to be bolted down) unless they are mounted per Fluid Metering, Inc.

specifications, if not injury may occur and/or damage to unit.

Do not touch any rotating pump or motor components: injury may

occur.

Do not run pump dry, unless designed for that service.

Running dry is harmful to the pump, and will cause excessive heating

due to internal friction.

Check pump rotation and inlet/outlet pump port orientation before

connecting power to pump. If not injury may occur.

When pulling out cords from outlets do not pull cord, grasp plug to

prevent plug damage or electrical shock.

Fluid Metering, Inc. Drive Motors become HOT and can cause

a burn

. DO NOT TOUCH!

Turn off the electrical power before checking pump for any problems.

Connect motor, speed controllers, or any other electrical devices

based on Fluid Metering Inc. specifications. Any unauthorized work

performed on the product by the purchaser or by third parties can im-

pair product functionality and thereby relieves Fluid Metering, Inc.

of all warranty claims or liability for any misuse that will cause

damage to product and/or injury to the individual.

Power cables and leads should not be bent, pulled or inserted by ex-

cessive force. Otherwise there is a threat of electrical shock or fire.

Replace any inline fuses only with fuse rating as specified by Fluid Me-

tering, Inc.

When pump/drive is under operation, never point discharge tubing into

face or touch any rotating components of pump.

In a power down thermal overload cut-in condition, unplug or turn off

power to pump. Always allow a cool down period before restarting:

otherwise, injury or damage may occur.

For 30 seconds after power is removed from pump/drive: do not

touch any output terminals. Electrical shock may occur because of

residual voltage.

SAFETY INSTRUCTIONS

General Instructions

Congratulations! You are about to install the newest technology from FMI, designed specifically

for industrial dispense applications, where long-term trouble-free performance is expected. If

you have any questions during any stage of your installation please don't hesitate to give us a

call. Our technical staff is ready with answers. Call us at 1-800-223-3388. LET'S GET

STARTED!

Your controller is initially set to provide one dispense per signal at 320 strokes per minute.* Dis-

pense signal, other speed settings, and dispense values are easily set by following the detailed

instructions on the following pages. * Best speed for most dispense applications.

Connect cable from CONNECTOR P1 on the housing to your PLC or controller and power sup-

ply as per the following pin connections. NOTE: Not all the available functions may be suitable

for your application; therefore some wires may not need to be connected.

IN-IDS-08

IDS INDUSTRIAL DISPENSER

INSTRUCTIONS

1 2 3 4 5 6 ... 13 14

Inhaltsverzeichnis

Seite 1 - General Instructions

Before using any Fluid Metering, Inc. product read the following safety instructions as well as specific product specifications and operating instruct

Seite 2 - FIGURE 1

IDS INDUSTRIAL DISPENSERINSTRUCTIONSIN-IDS-08101IDS-“Q” Pumpheaddirection <right to leftDisplacement is adjusted bychanging Angle of pumphead.Loose

Seite 3 - *#8 Always off

IDS INDUSTRIAL DISPENSERINSTRUCTIONSIN-IDS-08 ALL OILS AND PARTICLES. BE SURE THE SURFACE INSTALLATION INSTRUCTIONS FOR MOUNTING8. REPLACE WITH A

Seite 4 - Dispense control

IDS INDUSTRIAL DISPENSERINSTRUCTIONSIN-IDS-081IDS2000A / IDS2000AGMFMI P/N IDS2000A / IDS2000AGMDWG NOTITLESHT 2 OF 2Fluid Metering Inc.REV5 Aeria

Seite 5

IDS INDUSTRIAL DISPENSERINSTRUCTIONSIN-IDS-081IDS2000A / IDS2000AGMFMI P/N IDS2000A / IDS2000AGMDWG NOTITLESHT 1 OF 2Fluid Metering Inc.REV5 Aerial

Seite 6

IDS INDUSTRIAL DISPENSERINSTRUCTIONSIN-IDS-08FINISHSURFACEFINISHChemical Metering PumpsTOLERANCESU NLESS OT HER WISESPECIFIED.X = ±.015.XX = ±.010.XX

Seite 7 - 'RED' Jum

IN-IDS-08IN-IDS-082The following connections are made through the 6' cable provided. It has a nine-pin Amp Series 1, Cir-cular Connector, shell

Seite 8

IDS INDUSTRIAL DISPENSERINSTRUCTIONS311.0 DescriptionThe IDS Industrial Dispenser has a stepper motor and a self-contained step motor controller s

Seite 9

IN-IDS-084OPEN12412811109 'RED' JumperDispense controlswitchboard DispenseSwitches64032016080402010OFFSPEED[RPM]OFFFLUID METERING INC.PCB

Seite 10 - INSTRUCTIONS

IN-IDS-085VOLTS OPTO-OUTPUTOHMSTRANSISTOR OUTPUTOHMSRELAY OUTPUT, OHMS6 220 220 2709 390 390 47012 620 620 68015 820 820 82018 1000 1000 100024 1300 1

Seite 11

IN-IDS-0862.4 External Control 0-5 VDC - Voltage Following Input ModeIn order for the stepper controller board to recognize and accept a 0-5 VDC c

Seite 12

IDS INDUSTRIAL DISPENSERINSTRUCTIONSIN-IDS-087OPEN12412811109 'RED' JumperDispense controlswitchboardDispenseSwitches64032016080402010OFFS

Seite 13

IN-IDS-088FIGURE 4 (200145)IDS INDUSTRIAL DISPENSERINSTRUCTIONS1

Seite 14 - FMI P/N IDS2000A SERIES

IDS INDUSTRIAL DISPENSERINSTRUCTIONS9Interchangeable pumphead modules permit this industrial dispenser to beFLOW RANGE IDS FLOW INFORMATIONInterchange